Your watercooling and modding distributor Your watercooling and modding distributor

Alphacool Eisbecher 250mm Plexi reservoar

  • 1011217
  • 15194
  • 4250197151948
  • 0,768 kg

Leverans: i 5 - 6 dagar

523,00 kr *

Kostnad inkl. VAT plus fraktkostnader

Rekommenderade tillbehör
Extra kostnad
Alphacool Aurora LED Ring 60mm - röd
1x
Alphacool Aurora LED Ring 60mm - röd
165,88 kr*
Alphacool Aurora LED Ring 60mm - vit
1x
Alphacool Aurora LED Ring 60mm - vit
155,38 kr*
Alphacool Aurora LED Ring 60mm - uv
1x
Alphacool Aurora LED Ring 60mm - uv
165,88 kr*
Alphacool Aurora LED Ring 60mm - blå
1x
Alphacool Aurora LED Ring 60mm - blå
165,88 kr*
Alphacool Aurora LED Ring 60mm - grön
1x
Alphacool Aurora LED Ring 60mm - grön
165,88 kr*
Alphacool 120/140mm monteringsfäste Alphacool Eisbecher - 2 st
1x
Alphacool 120/140mm monteringsfäste Alphacool Eisbecher - 2 st
92,38 kr*
Alphacool Aurora LED Ring 60mm - RGB
1x
Alphacool Aurora LED Ring 60mm - RGB
228,88 kr*
Tekniska detaljer och videor mer
Tekniska detaljer
Anslutning: G1/4" innergänga
Antal anslutningar: 6
Dimensioner: 60 x 60 x 250mm
Fillport: G1/4" inre gänga
Färg: Transparent
Förinstallerad pump: Nej
Kompabilitet: till flödespumpar
LED hål: Tillgänglig (för 5mm LEDs)
Material: Plexiglas
Tillverkare: Alphacool
Typ av reservoar: Reservoar 60mm
Videor

Reinvent the tube   The Eisbecher Series consist of 20 different reservoirs that differ...mer
Produktinformation


Reinvent the tube 

The Eisbecher Series consist of 20 different reservoirs that differ between usage, measurement and appearance. There are ten reservoirs within this series that consist of 99% plexi - totally unique! But the main difference between these reservoirs is within the functionality of the different sockets.


Constituents

Bubble Down
It is placed at the bottom of the reservoir to prevent turbulences that could lead air into the watercircle. 

Lighttower Standpipe
The "Lighttower" effect creates an astounding visual experience within every watercooling system. The Eisbecher supports this in two different ways: fluid coming from the bottom and coming from the top. The water is being led through the standpipe to the bottom or to the top where it splashes out of eight evenly distributed holes at the end of the pipe to the inner wall of the reservoir. This special watergame is the so called "Lighttower" effect. 

Stand
The known feet from the "Eisdecken" find its very way even to the Eisbecher and sustain every combination with a solid stand.


Mountings
There are two mountings placed above and under the pipe for fastening the lot in the casing. The holes in this mounting have a spacing of a 120/140 cooling fan.You can reduce the width of the mountings up to the width of the reservoir and there are three M4 threads availaible per mounting for fastening if you would rather not mount the reservoir at the fan space. These mountings are easily removeable especially when not being used. You will find these mountings on all 20 reservoirs.

Lighting module
The lighting modules consist of plexi and enable the lighting with a 5mm LED. These modules can be installed into all 1/4" holes. They are being used in the lid and occasionally in the socket of the reservoir. This facilitates a unique way to your personalised lighting effects.

Material
All models of the reservoir are availaible in acetal and plexi. So there is something for everone.

Measurements

All reservoirs are availaible in two different sizes: the 150mm version and the 10cm bigger 250mm version. The smaller reservoir comes with only one standpipe coming from the bottom because of its size and the bigger reservoir comes with two: one coming from the top and the other one from the bottom.











 

The Eisbecher

There are two additional versions for everyone that would rather operate the pump seperately. The Bubble Down and depending on the size one or two standpipes that fascilitate the "Lighttower" effect and two lighting modules one from the top and the other one from the bottom are being used here. And there are additional three LED holes for the plexi version to maximize the lighting power. The openings to fill or drain the liquid are doubled here: One at the side and one at the bottom.

Included in delivery:

  • 8x M4x8mm screw
  • 4x M4 nut
  • 2x G1/4" locking screw
  • 1x allen key 2,5mm

 

Measurements 250mm Version:
Measurements with mounting (LxWxD): 251 x 136 x 79,5mm
Measurements without mounting(LxW): 251 x 60mm

Diameter of the Plexitube: 60mm



Notice:

In order to use the intake from the top, a G1/4” extension piece is necessary (article 1011183-1011186), since the screw thread is embedded a few mm into the lid and many compression fittings will not be able to be screwed in. 

Utmärkelser
Frågor & Svar mer
Frågor & Svar
Frage von Axel J. vom 02. February 2016
Ich wollte mal wissen, ob die LED`s dabei sind, oder ob man sie extra bestellen muss?
Antwort von Administrator vom 02. February 2016
Die werden extra bestellt :)
Antwort von Daniel N. vom 03. March 2016
Kann man den auch als standalone agb hernehmen?
Frage von Philip H. vom 07. July 2016
Guten Abend, der Artikel: 1011191 müsste doch an den beiden unteren Stellen passen?
Antwort von Administrator vom 07. July 2016
Passt ohne weiteres :)
Frage von Philipp H. vom 11. November 2016
Kann man diesen Behälter auch benutzen wenn man keine pumpe unten anschließt ?
Antwort von Wieland B. vom 12. December 2016
Dieser Behälter ist nur für eine solche Benutzung ausgelegt, jedoch muss aber in dem Kreislauf eine Pumpe eingebunden sein.
Frage von Dominik K. vom 01. January 2017
Kann man den Lighttower Effekt irgendwie unterbinden? Durch das ständige sprudeln ist die Flüssigkeit im AGB nicht so klar sondern matt.
Antwort von Dominik K. vom 01. January 2017
Sorry, war mein Fehler. Es lag an der Kühlflüssigkeit selber, warum diese so matt und nicht klar war. Aber dennoch würde mich interessieren, ob man den Lighttowereffekt bei Bedarf ausstellen kann?
Frage von Dominik K. vom 01. January 2017
Sorry, war mein Fehler. Es lag an der Kühlflüssigkeit selber, warum diese so matt und nicht klar war. Aber dennoch würde mich interessieren, ob man den Lighttowereffekt bei Bedarf ausstellen kann?
Antwort von Administrator vom 02. February 2017
Wenn sie den Effekt ausschalten wollen, dann befüllen sie den Eisbecher einfach bis über das Steigrohr.

Haben Sie eine Frage?

Hinweis: Ihre Frage wird öffentlich einsehbar sein und kann - neben unserem Support - auch durch ein Mitglied unserer community beantwortet werden. Sie können Ihren öffentlich sichtbaren Namen und Ihre Email Benachrichtigungen in Ihrem Kundenkonto konfigurieren.
Läs, skriv och diskutera recensionermer
Recensioner
5 Stjärna:
(0)
4 Stjärna:
(0)
3 Stjärna:
(0)
2 Stjärna:
(0)
1 Stjärna:
(0)
antikorrision AntiCorro-Vätska 50ml antikorrision AntiCorro-Vätska 50ml
Innehåll 50 ml (942,50 kr * / 1000 ml)
47,13 kr *